全自动KN95口罩机

  • 型号:

    YD-QZDKN95-001
  • 产品别称:

    KN95口罩,耳挂式KN95口罩机,口罩机生产线
  • 主要组成部分:

    打片机、焊耳机
  • 现货:

  • 速度:

    40pcs/min

同类产品推荐

  • 全自动KF94口罩机
  • 平面一拖一口罩机
  • 平面焊耳机
  • KN95焊耳机

139-2940-8368

180-2515-1739

  • 产品详情

 

 

 
 
生产节拍 :40±5pcs/min
机台功率 :最大功率20KW
(超音波2.6KW*2 + 2KW*2 + 设备其他10.8KW)
气源:压缩空气要稳定在0.5Mpa以上
直径12的气管:接三联件,预留2个接口
电源:220V  16A
外形尺寸mm:9800(L)*1400(W)*2000(H)
 
Production cycle: 40±5pcs/min
Machine power: maximum power 20KW
(Ultrasonic 2.6KW*2 + 2KW*2 + other equipment 10.8KW)
Air source: compressed air should be stabilized above 0.5Mpa
Trachea with a diameter of 12: connect to the triple piece, and reserve 2 ports
Power supply: 220V 16A
Dimensions mm: 9800(L)*1400(W)*2000(H)
 
 
KN95口罩机由以下设备组成:六层原材料上料机构、鼻梁&压纹工序、焊接耳带工序、打码(根据需求选配喷码或者激光打标)、成本裁切&废料处理工序。
 
The KN95 mask machine consists of the following equipment: six-layer raw material feeding mechanism, nose bridge & embossing process, welding ear strap process, coding (optional inkjet or laser marking according to requirements), cost cutting & waste treatment process.
 
设备动作流程:1、原材料上料(根据产品要求放置四层布料或五层布料)→推鼻梁条→本体滚花→左耳带焊接→右耳带焊接→打码(根据需求选配喷码或者激光打标)→折边→封边→成本裁切→成品排出
Equipment action process: 1. Raw material loading (place four or five layers of fabric according to product requirements) → push nose bridge → body knurling → left ear band welding → right ear band welding → coding (optional coding according to requirements Or laser marking) → folding → edge banding → cost cutting → finished product discharge
 
安装要求
1、检查地面的承受力和平整度,综合考虑机器的总重量和机器在运转时引起的振动。
2、水平放置机器,调整各机脚使其处于水平状态。
3、接通电源之前,仔细检查各连接是否松动。
4、正确连接电源。
5、需要的电源为AC 220V /50Hz。
Installation requirements
1. Check the bearing capacity and flatness of the ground, comprehensively consider the total weight of the machine and the vibration caused by the machine during operation.
2. Place the machine horizontally and adjust the feet of each machine to make it level.
3. Before turning on the power, carefully check whether the connections are loose.
4. Connect the power supply correctly.
5. The required power supply is AC 220V/50Hz.
 
设备维护
设备的日常维护和保养是保证设备运行良好,降低故障发生率和提高设
备使用寿命的有效手段。客户在使用设备进行生产活动时,应特别予以重视。
1、操作人员在操作设备的过程中,应密切注意设备的运转情况,做好设备运转记录,详细记录本班设备的运转情况,供设备维护人员在检查和维护设备时参考。
2、发现异常,必须马上停机,通知维修人员处理,故障排除后方可重新开机。
3、设备维护人员应对设备进行定期的检查、维护和保养。
4、保养设备前,必须先断开电源,并遵守相关安全规范。
5、任何固定的保护装置因保养需要打开或者移走,保养完毕后,必须完整无损地回复原位。
Equipment maintenance
The daily maintenance of the equipment is to ensure that the equipment is running well, reduce the failure rate and improve the equipment.
Effective means to prepare the service life. Customers should pay special attention when using equipment for production activities.
1. In the process of operating the equipment, the operator should pay close attention to the operation of the equipment, make a record of the equipment operation, and record the operation of the equipment in the class in detail for the equipment maintenance personnel to refer to when inspecting and maintaining the equipment.
2. If an abnormality is found, the machine must be shut down immediately, and the maintenance personnel must be notified to deal with it, and the machine can be restarted after the fault is eliminated.
3. The equipment maintenance personnel shall conduct regular inspection, maintenance and maintenance of the equipment.
4. Before servicing the equipment, you must disconnect the power supply and follow the relevant safety regulations.
5. Any fixed protection device needs to be opened or removed due to maintenance. After maintenance, it must be restored to its original position intact.

 

标签:  KN95口罩机
分享到: